Key takeaways

  • Power off at the breaker and a licensed electrician to disconnect it, then drain it, before anyone touches it.
  • The standard method: tip the empty tub onto its side, onto a spa dolly, and roll it. Hot Spring lists its spas at 29 to 38 inches wide on their side.
  • Measure the narrowest point on the route. A 90° turn needs room for the full length, because a spa doesn't bend.
  • Plan on three or four people (Angi). An empty 7-seat tub can weigh 790 lb, and the dolly should carry it, not the crew.
  • Angi: $300 to $1,200 for an off-site move, $200 to $400 on the same property. Add an electrician at both ends.
  • Old, cracked or failing? Moving it may cost more than it's worth. Removal starts from $349.

Moving a hot tub is a heavy, awkward job, but it's not complicated. The tub travels empty, on its side, on a dolly, with a crew and a planned route. This guide covers each step, the equipment, the measurements that decide whether it fits, and what professional hot tub movers charge.

One thing up front: Hot Tub Haulers removes hot tubs. We don't relocate working spas. If your tub is worth keeping, a spa dealer or a hot tub mover is who you want, and the steps below will help you plan the job or check their quote. If it isn't worth keeping, skip to move it or remove it?

Can you move a hot tub yourself?

You can, with the right gear and enough people. Angi's guidance is blunt: it doesn't recommend DIY. Even drained, it says a hot tub can weigh 500 to 1,000 pounds. If you go ahead anyway, it says you'll need at least two other people, a dolly, lifting and tie-down straps, 4x4 lumber for base support and moving blankets.

Spa makers say much the same. Hot Spring's moving FAQ says the best way to move a hot tub safely is to leave it to the professionals. For a short move across a flat, level yard, a careful crew can do it. Stairs, slopes, tight gates or a trailer ride raise the risk to people and to the tub.

Step 1: prepare the hot tub

Power off, and a licensed electrician to disconnect it

Turn the spa off at the breaker first. The switch on the spa controls the spa, not the supply. Most full-size spas are hard-wired: Hot Spring's 230V models need a 50 amp breaker and a GFCI subpanel at least 5 feet from the water's edge. A licensed electrician should disconnect a hard-wired spa and make the circuit safe. Don't pull conductors out of a disconnect box yourself. A 120V plug-in spa only needs unplugging.

Our hot tub disconnect guide covers what the electrician does and what the code asks for.

Drain it, following your city's rules

A hot tub always moves empty. Hot Spring lists its 7-seat Grandee at 455 gallons. The rules for where that water can go are local. Three examples from our city guides:

  • Phoenix: City Code Chapter 32C bars pool water from storm drains. Use the house sewer clean-out at no more than 12 gallons per minute. Phoenix guide
  • Seattle: Seattle Public Utilities says spa water goes to the sanitary sewer, or to a storm drain only if it's dechlorinated to 0.1 ppm or less and pH-adjusted. Seattle guide
  • Minneapolis: the city's pool ordinance calls for emptying to the sanitary sewer, never onto streets, sidewalks or a neighbor's land. Minneapolis guide

Our guide to draining a hot tub walks through the drain valve, a submersible pump, and the rules in hundreds of cities. Sponge or towel out the footwell afterward. For a long move, Hot Spring suggests draining thoroughly and letting the spa dry out, so trapped water doesn't leak onto your other belongings in transit.

Cover off, steps and loose parts off

Take off the cover and any cover lifter, steps, handrails and loose accessories. They travel separately. Take photos of the tub from every side before the move. Hot Spring recommends documenting its condition so you can use the mover's insurance if something breaks.

A teal acrylic hot tub with its front cabinet panel off, sitting on a pad in a side yard between a wooden deck, a vinyl fence and a metal railing, with its steps and cover set beside it.
A typical side-yard spot: deck on one side, railing on the other, and a single route out. Removal & photo: Tally Junk Removal (Tallahassee, FL), shown with permission · not a Hot Tub Haulers job.

How much does a hot tub weigh empty?

Use your own model's spec sheet. These manufacturer figures show the range:

ModelSizeDry weightFilled weight
Hot Spring Vanguard (6 seats)7′3″ × 7′3″ × 36″695 lb4,540 lb*
Hot Spring Grandee (7 seats)8′4″ × 7′7″ × 38″790 lb5,810 lb*
Bullfrog S200 swim spa17′ × 7′10″ × 4′4″2,720 lb18,950 lb

*Hot Spring's filled weights include water and adults at 175 lb each. Sources: Hot Spring and Bullfrog spec sheets.

Two points matter for moving. First, never try to move a tub with water in it. Second, an old tub may weigh more than its spec sheet: water that leaks into the foam insulation stays there. A swim spa is a different job altogether, and usually a specialist's.

Hot tub moving equipment

EquipmentWhat it's forWhat to look for
Spa dolly or spa cartCarries the tub on its side so the crew doesn'tRated well above your tub's dry weight. CasterHQ's oak hot tub dolly, for example, is rated 1,400 lb, with a 50 × 28 in deck, 10 in pneumatic wheels and a height of 14 3/16 in. Pneumatic tires handle grass and gravel.
4x4 lumberBlocks the raised edge while you get hands and the dolly under itAngi lists 4x4 boards for base support.
Lifting and tie-down strapsHold the tub to the dolly, then to the trailerRatchet straps with a working load limit marked on the label.
Rollers or pipeShort moves across a flat, hard surfaceOnly on level concrete or pavers. Not on slopes, steps or lawn.
Plywood sheetsA track across lawn, soft ground or a lipThick enough not to flex under the dolly's wheels. Overlap the joints.
Moving blanketsProtect the cabinet and acrylic lip, and pad the pivot edgeAngi lists moving blankets to prevent damage in transit.
TrailerOff-site movesA ramp and tie-down rings. U-Haul's 6x12 utility trailer with ramp is 12 × 6 ft inside, carries up to 2,670 lb and has tie-down rings.

Angi's DIY budget: $200 to $400 for supplies, plus $50 to $3,500 for a truck rental depending on size and distance.

How many people does it take to move a hot tub?

Angi says most hot tub moves take three to four movers. Do the math and it's clear why the dolly matters. NIOSH's lifting guidance puts the maximum two-handed lift, under ideal conditions, at 51 pounds. A 790 lb tub split four ways is nearly 200 pounds each. So the crew's job is to tip, balance and steer. The dolly takes the weight.

A sensible crew for a standard 6 to 7 seat tub:

  • Two people on the high side, controlling the tip.
  • One or two on the low side, guiding the tub down onto the dolly and keeping hands and feet clear.
  • One person who calls each move, so everyone lifts and stops together.

Stop if you're short-handed. Don't try to catch a falling tub.

The side-tip method, step by step

This is the best way to move a hot tub, and it's how spas are delivered in the first place. Hot Spring's delivery-access table gives each spa's dimensions "laid on its side", because that's how it rolls in.

Diagram of the side-tip method in four side views: the empty tub sits flat with its cover off; one edge is lifted and a 4x4 slid under it; the tub is tipped up onto its side over a padded edge; the tub stands on its side on a spa dolly, held by two straps. A note says a Hot Spring Grandee on its side is 38 inches wide and 7 feet 7 inches tall, about 8 feet 9 inches on a 14 3/16 inch dolly.
The side-tip method. Dimensions from Hot Spring's pre-delivery instructions and CasterHQ's dolly listing. Diagram: Hot Tub Haulers.
  1. Clear and protect the route. Walk it first. Move anything in the way, open or remove the gate, and lay plywood over grass or soft ground.
  2. Pick the side it will stand on. Choose the long side that faces the direction of travel. Pad that bottom edge with a blanket so the cabinet doesn't crush as it pivots.
  3. Lift one edge and block it. With the crew on the opposite long side, lift that edge a few inches and slide a 4x4 under it. Now everyone can get their hands under the tub.
  4. Tip it up, slowly. On the caller's count, lift the high side, walking hands up the cabinet, until the tub stands on its padded edge. Keep it moving at walking pace and don't let it go past vertical.
  5. Get the dolly under it. Tilt the standing tub a few inches toward the crew, slide the spa dolly under the low edge, and lower it back down. Center it.
  6. Strap it. Two straps around the tub and the dolly, tight enough that the tub can't rock on the deck.
  7. Roll it. One person steers at each end and one or two steady the top. Go slowly on any slope, and keep someone on the downhill side. Never stand where the tub would fall.

To set it down, reverse the steps: off the dolly onto the padded edge, then lower the high side onto blocks and slide them out.

Plan the route: gate width vs. tub dimensions

On its side, a tub's thickness becomes its width and its length becomes its height. Hot Spring's instructions say to use the dolly's width or the spa's width on its side, whichever is greater, for the width you need. Use the length for any sharp turn. Here are its Highlife models:

Hot Spring modelWidth W (on its side)Length LHeight H (on its side)
Grandee38″8′4″7′7″
Envoy38″7′9″7′7″
Vanguard36″7′3″7′3″
Aria36″7′3″7′3″
Sovereign33″7′9″6′8″
Triumph33″7′9″6′2″
Prodigy33″7′0″6′6″
Jetsetter LX33″7′0″5′5″
Jetsetter29″7′0″5′5″

Source: Hot Spring Highlife pre-delivery instructions. Hot Spring notes all dimensions are approximate: measure your own spa.

Top-down diagram of a 38 inch thick tub on its side passing through a 42 inch clear gate with about 2 inches each side, next to the same tub blocked by a 36 inch gate. A table lists Hot Spring widths on their side from 29 to 38 inches, and notes cover turns, latches, meters and overhead clearance.
The gate-width check. Widths from Hot Spring's pre-delivery instructions; Master Spas says at least 38 inches of gate width is ideal. Diagram: Hot Tub Haulers.

How to measure the route

  1. Measure the tub on its side. That's the cabinet height, the 36 or 38 inches you'd stand next to. Add anything that sticks out, like a cover lifter bracket.
  2. Measure every gap, at its narrowest. Gate posts, latches, hinges, downspouts. Hot Spring's checklist calls out protruding electric meters, gas meters and A/C units.
  3. Check the turns. Hot Spring is clear: at a 90° turn, the spa will not bend. The tub's full length has to swing through the corner.
  4. Check overhead. Add the dolly's height to the tub's height on its side. A Grandee on a 14 3/16 in dolly is about 8 ft 9 in tall. Look for eaves, gutters, pergolas and branches.
  5. Count steps. Hot Spring's checklist allows no more than 6 consecutive stairs without a landing.

Too narrow? Hot Spring says it may be necessary to remove a gate, part of a fence, or other movable obstructions. If that won't do it, it's a crane.

When you need a crane

Hot Spring says that about ten percent of the time, a crane is the only way to install a spa. That happens when the tub has to go over a wall because the entry is too narrow, the eaves too low, the corner too tight or the stairs too steep. Angi puts crane delivery at $800 to $1,500 or more and says it's needed in 5% to 10% of installations.

A crane move is the same job in reverse. The tub is drained, disconnected and rigged, then lifted over the house or wall to the street. A crane parked on the street may need a city permit, and that can take longer than the move itself. Our edge cases page covers rooftop, balcony and backyard-locked spas.

A teal hot tub with a partly removed cabinet under a wooden pergola on a brick-paver patio, with lattice behind it and an awning overhead.
A tub under a pergola has an overhead limit as well as a width limit. Removal & photo: All Out Rubbish (Palm Beach County, FL), shown with permission · not a Hot Tub Haulers job.

Moving a hot tub to a new house

Loading the trailer

A tub travels best the way it rolled: on its side. On its side, a Grandee's footprint is about 38 inches by 8 ft 4 in, which fits inside a 12 × 6 ft trailer. Laid flat, a 7 ft 3 in tub is wider than that trailer's 6 ft interior. Check your tub's dry weight against the trailer's rated load, and the trailer against your tow vehicle's rating.

  1. Roll the dolly up the ramp with people on the downhill side steadying the top, never behind it.
  2. Stand the tub against the front of the trailer, or block it so it can't slide forward.
  3. Strap it to the trailer's tie-down rings, not to the dolly alone.
  4. Pad every strap where it crosses the acrylic lip or a cabinet corner.

How many tie-downs?

The federal cargo-securement rules for commercial trucks are a useful benchmark for a private trailer. 49 CFR 393.110 calls for at least two tie-downs for an article longer than 5 feet, and 393.106 says the combined working load limit of the tie-downs must be at least half the cargo's weight. For a 790 lb tub, that's at least 395 lb of combined rated strap capacity, a minimum, not a target. Use more straps than that, check them after the first mile, and drive slowly. Your state's rules for trailers and loads apply; check them.

Get the new spot ready first

Before the tub arrives, the new site needs a level base that can carry the filled weight. For the Grandee, Hot Spring requires a reinforced concrete pad at least four inches thick if it sits outdoors. On a deck or indoors, it says to consult a qualified building contractor or structural engineer. The electrician should also have the new circuit ready.

Rather not deal with it? We remove hot tubs from $349 — cut-down, haul-away and disposal included.

Get a hot tub removal quote ↗

Reconnecting the hot tub

  • A licensed electrician connects it. Hot Spring says all electrical circuits must be installed by a qualified, licensed electrician. A 230V Hot Spring spa needs a dedicated 50 amp breaker, and the GFCI subpanel must be at least 5 feet from the water's edge.
  • Expect a permit. Hot Spring notes that in most cities and counties, permits are required to install electrical circuits. See do you need a permit? and confirm with your local building department.
  • Close out the old circuit. At the house you're leaving, the empty circuit should be made safe too. A live, abandoned disconnect is a common home-inspection write-up.
  • Level it, fill it, test it. Hot Spring says the spa must be level for its plumbing to drain properly. Check for leaks at the pack after the first fill, since a move can shake fittings.

Angi lists a new connection at $85 to $210 among its relocation costs. If the new house needs a circuit, Angi puts hot tub wiring at $600 to $2,200.

How much does it cost to move a hot tub?

These are each guide's own published figures, not our prices. We don't move hot tubs.

ItemPublished costSource
Hot tub movers, national average$600 (most pay $300–$1,200)Angi
On-site move (same property)$200–$400Angi; Hot Spring
Off-site move, pickup and delivery$300–$1,200Angi
Relocating, by distance$150–$1,000HomeGuide
Mover labor$25–$50 per mover per hourAngi
Repairs after transit$170–$540 for common fixesAngi
New electrical connection$85–$210Angi
Crane, when access requires it$800–$1,500+Angi (crane delivery)
DIY supplies, plus truck rental$200–$400, plus $50–$3,500Angi

What changes the price, per Angi and Hot Spring: the tub's size, yard access at both ends, distance, stairs or elevation, crew size, and whether a crane or forklift is needed. Hot Spring adds that the highest quote it found was $750 to $1,000 for an on-site move in the New York City area. Dense areas with more obstacles cost more.

Moving fees usually aren't the whole bill. Hot Spring says draining and disconnection are not included in most hot tub moving services. Add the electrician at both ends, a permit if one is required, and a repair allowance.

Hot tub movers: who to call, and what to ask

Hot Spring lists three kinds of professional: a local hot tub dealer, a dealer-related service provider, or an independent moving company. It adds that many dealers don't do off-site moves but can refer you. For an out-of-state move, a long-distance mover may bundle the spa with the rest of your belongings.

Questions to ask any hot tub mover:

  • Is the price flat or hourly? How many crew, and how long?
  • Does it include draining, disconnecting or reconnecting? Most won't.
  • What insurance covers the tub in transit, and what does full-value protection cost?
  • Have they seen photos of the route, the gate and any stairs?
  • What happens if it won't fit, and who arranges a crane?
  • Will they set it on the new pad and help level it?

Mistakes to avoid

  • Moving it with any water in it. Water sloshes, shifts the balance and adds weight. Drain and sponge it out.
  • Trusting the spa's own switch. Kill power at the breaker, and have an electrician disconnect a hard-wired tub.
  • Measuring the gate, not the narrowest point. The latch, the meter or the A/C unit is what stops you.
  • Forgetting the turn. A tub that fits the gate can still jam at a corner.
  • Too few people. Three or four for a standard tub. Stop if you're short.
  • Strapping to the dolly only. On a trailer, strap to the trailer's rings and block the base.
  • Draining into the street. Most cities send spa water to the sanitary sewer. Check yours first.
  • No site at the other end. A spa needs a level base that can carry its filled weight, and a circuit.

Move it or remove it?

Angi's own advice: moving a hot tub is worth it if it's in good condition, you use it often, and the move costs a reasonable amount compared with a new one. If it's old, needs extensive repairs, or the move is very expensive, it may not be worth it. Here's how to decide.

FactorPoints to moving itPoints to removing it
ConditionDry foam, no cracks below the waterline, the pack heats and holds temperatureA cracked shell, wet foam, a dead pack, error codes
AgeNewer, with features you'd buy againOlder and short on the features of newer spas, as Hot Spring notes
Cost to move vs. replaceMove, reconnection and repairs come to a small share of a new tub. Angi puts new 6–7 seat tubs at $3,000–$15,000.Moving ($300–$1,200), reconnection and likely repairs ($170–$540) approach what a newer tub would cost
The new homeThere's a level pad, room on the route and a circuit, or it's cheap to addNo pad, no circuit, or a backyard that needs a crane
The home you're leavingThe buyer doesn't want itThe buyer wants it left. Hot Spring notes a spa can make a home more appealing to buyers. Ask your agent.

To check condition quickly, run our rehoming test. If it passes and you don't want it, you may be able to sell it or give it away. Hot Spring also says nearly all spa dealers will haul away your current spa for free when you buy a new one, and many offer a trade-in.

If it fails, don't pay to move it. You'd be paying to transport something you'll soon pay to remove. That's where we come in. We cut it down, carry it out, haul it away and handle the disposal, from $349. Send a few photos of the tub and the route out and we'll send you a price. See pricing, what hot tub removal costs, or check where we work.

Rather not deal with it? We remove hot tubs from $349 — cut-down, haul-away and disposal included.

Get a hot tub removal quote ↗

Frequently asked questions

What is the best way to move a hot tub?

Drain it, have it disconnected, then tip it onto its side onto a spa dolly and roll it, with three or four people. On its side, a tub only needs a path as wide as its thickness, which is often 33 to 38 inches, instead of its full 7 or 8 feet.

How much does it cost to move a hot tub?

Angi puts the national average for hot tub movers at $600, with most people paying $300 to $1,200 for an off-site move and $200 to $400 to move a tub to another spot on the same property. Budget separately for the electrician at both ends and any repairs after the move.

How many people does it take to move a hot tub?

Angi says most hot tub moves need three to four movers, and at least two helpers besides you if you do it yourself. Even a 695 to 790 lb empty tub is far more than people should carry, so the crew tips and steers while a spa dolly takes the weight.

Can a hot tub fit through a 36 inch gate?

Only if its thickness on its side is less than 36 inches. Hot Spring lists its Highlife spas at 29 to 38 inches wide on their side, so some fit and some don't. Measure your own tub and the narrowest point of the route, including latches and meters.

Do I need an electrician to move a hot tub?

Yes, for a hard-wired spa. A licensed electrician should disconnect it before the move and connect it at the new spot, and Hot Spring notes that most cities and counties require permits to install electrical circuits. A 120V plug-in spa only needs unplugging.

Is it worth moving an old hot tub?

Often not. If the shell is cracked, the foam is wet or the pack is failing, you'd pay to move something you'll soon pay to remove. Compare the full moving cost, with reconnection and likely repairs, against the price of a newer tub or simply leaving it.

Sources